NPTEL Introduction To Internet Of Things Week 5 Assignment Solutions
NPTEL Introduction To Internet Of Things Week 5 Assignment Answers 2023
1. Company ABC manufactures a room temperature monitor which sends data via protocol X and company MNO manufactures another kind of room temperature sensor which sends data via protocol Y. With respect to this, which among the following correctly captures the said scenario?
a. Homogeneity of IoT
b. Heterogeneity of IoT
Answer :-For Answer Click Here
2. When two IoT devices wish to communicate, semantic conflict in such a scenario in IoT interoperability refers to____________________.
a. Two devices built by the same manufacturer
b. Two devices sensing the same physical parameter
c. Two devices having different deployment location
d. Two devices having different processing and business logic
Answer :- For Answer Click Here
3. Which of the following issues needs to be addressed while solving user interoperability?
a. Device characterization and identification
b. Syntactic interoperability
c. Semantic interoperability
d. All of these
Answer :- For Answer Click Here
4. Which UMB interoperability component is responsible for converting physical devices into virtually abstracted ones?
a. UMB Adaptor
b. UMB Core
c. UMB Hypervisor
d. UMB Abstractor
Answer :- For Answer Click Here
5. A Protocol Translation Unit (PTU) acts as a middleware between two IoT devices with different native protocols to enable them communicate with each other by translating the language of one device to the other one and vice versa.
a. True
b. False
Answer :- For Answer Click Here
6. Suppose that a smart CCTV camera has been configured using C++ language. With respect to the device’s cosign identification as per the standard definition (A,B,C,D), which among the following the information “Configuration Lang:C++” will be most appropriately mapped ?
a. A
b. B
c. C
d. D
Answer :- For Answer Click Here
7. Which among the following are components of an Arduino UNO Board?
a. LED Power Indicator
b. Digital I/O Pins
c. Analog IN Pins
d. All of these
Answer :- For Answer Click Here
8. What is the series of micro controller chips powering Arduino UNO boards?
a. ATM series
b. X86 series
c. ARM 64 series
d. ATMEGA series
Answer :- For Answer Click Here
9. In Arduino IDE the ‘Verify’ and ‘Upload’ buttons perform the exact same task.
a. False
b. True
Answer :- For Answer Click Here
10. Suppose that an Arduino UNO board is connected to a pneumatic sensor which sends tyre pressure as floating point numbers. Which among the functions will you use to read from the sensor?
a. digitalRead()
b. analogWrite()
c. analogRead()
d. None of these
Answer :- For Answer Click Here
11. Consider the following Arduino sketch.
a. INPUT
b. OUTPUT
c. None of these
d. Anyone of these is okay
Answer :- For Answer Click Here
12. For integrating different types of sensors (such as DHT) with Arduino, you would need to install and #include the sensor specific libraries in your sketch.
a. True
b. False
Answer :- For Answer Click Here
13. Which of the following best describes the command given below?
ServoDemo.write(180);
a. Creates an instance of the servo
b. Pin writes 180 to the servo
c. Servo moves 180 degrees
d. All of these
Answer :- For Answer Click Here
14. In an Arduino sketch, for the default function void setup(), which of the following is true?
a. Point where the code terminates.
b. Point where the code starts.
c. It iterates over the different tasks in the program.
d. None of the above.
Answer :- For Answer Click Here
15. Which among the following can also be described as a relay, which is an actuator?
a. Pneumatic actuator
b. Motor type actuator
c. Electro-mechanical switch
d. Thermal switch
Answer :- For Answer Click Here
| Course Name | Introduction To Internet Of Things |
| Category | NPTEL Assignment Answer |
| Home | Click Here |
| Join Us on Telegram | Click Here |